Arecont Vision AV12176DN-28 IP Camera Driver
Day/Night Indoor/Outdoor Dome IP Cameras Delivering revolutionary flexibility, Arecont Vision SurroundVideo® Omni . AVDN Delivering revolutionary flexibility, Arecont Vision SurroundVideo® Omni Omni AVDN 12 Megapixel Network Camera - Color. 2 Table Of Contents SpaceCom Antennas for the MSAT Network. . The pin DIL located in the middle of the picture. . Installation Manual Inside the box: A. Arecont Vision SurroundVideo camera B. Mounting template C. SurroundVideo Omni INSTALLATION MANUAL AVDN-NL AVDN AVDN
|Supported systems:||Windows 2008, Windows XP, Windows Vista, Windows 7/8/10|
|Price:||Free* [*Free Regsitration Required]|
Arecont Vision AV12176DN-28 IP Camera Driver
General Pole Mount Kit Characteristics: It is a self-contained tracking antenna that uses patented beamsquint technology, which ensures that the antenna always points towards the satellite, regardless of Arecont Vision AV12176DN-28 IP Camera or ship movements. The antenna includes onboard LNA low noise amplifier ; HPA high power amplifier and tracking receiver circuitry to ensure communications even in adverse circumstances.
Unpacking After opening the box check the contents: One additional tracking IC satellite frequency chip with extra label.
The complementary IC is already installed in the antenna. Cables are not included in the basic antenna package. The following are approved cabling Arecont Vision AV12176DN-28 IP Camera Left coaxial connector N connects to the antenna. Molex plug in center is for 12 V DC. The DC cord is included.
Avoid exposure to microwave radiation. Keep a safe distance of min.
Arecont Vision®’s Innovative SurroundVideo® Omni Cameras
Keep a clear line of sight to the satellite. Preferably avoid all obstructions within 3 meter of the antenna. Obstructions less than 15 cm in diameter can be ignored beyond this distance. Do not locate the antenna close to interfering signal sources or receivers.
The red LED in the Junction Box will flash briefly and the antenna will initiate a search for the satellite. An overload can be triggered by a short circuit in either coaxial cables or connectors.
Check cables and connectors for faults. To reset the Junction Box you must cycle the power disconnect and reconnect 12 V DC Setting of antenna type Several antenna types can be selected from the setup menu of Westinghouse or Mitsubishi terminals.
- Arecont Vision SurroundVideo Omni AVDN Manuals
- 51 MPL PNG cliparts for free download UIHere
- Arecont 12MP WDR H.264 Omni-Directional Dome IP Camera
- AV12176DN-08 Arecont Vision
- How can we help?
- 51 MPL PNG cliparts for free download
SPAC-AC Designed for easy installation it ensures proper drainage of the antenna, galvanic insulation and is able to withstand the rigid mechanical stress encountered on a vehicle or ship. See drawing of pole mount kit in annex A.
Arecont Vision Avdn 12mp SurroundVideo Omni Network Dome Camera - WDR eBay
For temporary use or where drilling of holes is to be avoided a Magnetic Mount Installation Kit for the 2-axis antenna is offered. Changing the Tracking IC satellite frequency chipset. When ordering the antenna it is recommended that you indicate the satellite network MSAT1 or MSAT2 on which the unit will operate, thus ensuring delivery of the antenna with the proper IC installed as the default. However, if tracking of the alternate satellite is required, installation of Arecont Vision AV12176DN-28 IP Camera corresponding Tracking IC is necessary: Changing of tracking IC s involves opening the antenna radome and changing components on printed circuit boards.
Your browser security needs to be updated
This must be done by qualified personnel only, trained in handling static sensitive electronic components. Failure to observe these precautions can damage the antenna, causing problems in operation and void the warranty 9 To swap the Tracking IC: Turn the upper part ccw as seen from above about 60 degree.
This is a bayonet type lock, so there will be initial resistance. You must have the bottom part firmly fixed and use some amount of force to twist the upper part.
Then lift off the upper part. Locate the tracking IC: The pin Arecont Vision AV12176DN-28 IP Camera located in the middle of the picture. The tracking receiver has an access hole above the Tracking IC. You can remove the IC from the socket by gently inserting an ordinary small screwdriver from above into the narrow end - between the IC and the socket - and gently twist while pushing the screwdriver further under the IC.
Note orientation of the IC. Apply Arecont Vision AV12176DN-28 IP Camera bead of Dow Corning DC silicone to fasten the gasket around the base of the antenna. Align top and bottom a small index on the top above a square tap on the bottom - see picture then lower the upper part 11 and tighten the bayonet lock. Finally tighten the 3 set screws but only to the point that they are flush with the radome! Seal the two parts using sealing tape. As the seal provides long-term protection over a wide range of temperatures, humidity, UV radiation etc.
Failure to follow this guideline will void warranty.